Cabletron Systems Cabletron SmartSwitch Router 250 Guía de instalación Pagina 1

SmartSwitch™ Router 250ADSL-DMTQuick Start GuideP/N 222-00526-01

9To access Quick Start, you will first configure your PC to obtain an IP address automatically and then install the Quick Start program. The following

10Instructions:1. You should see the Network Neighborhood icon on yourdesktop. 4. In the TCP/IP Properties window, in the IP Address tab page, enable

115. Click OK.6. Answer Ye s to "Do you want to restart your computer?" Your computer will reboot. (Note: If your settings were already conf

12Windows 95, Windows 98, Windows NT 4.0:1. From your PC’s desktop, double-click My Computer.2. Double-click the Cabletron icon (your CD-ROM drive).3.

13Instructions:1. From the taskbar, click the Start button (located on your PC desktop).2. Select Programs. A pop-up list of your programs will appear

14After you have started the Quick Start application and have entered your password, you are ready to enter the following information in the Quick Sta

15If IP routing and NAT are enabled, you will be prompted to enter a Source WAN IP Address. You will obtain this information from your ISP or your Net

16•Domain Name•Server Address•Second Server5. OptionsThe following options are also available for further configuration of the router. Click Options M

17•Choose a PVCThe Quick Start application defaults the VPI/VCI numbers to 0 and 38 respectively, unless they have been preconfigured. Your Network Se

18•Execute ScriptThe router copies command files created on the PC and then executes them on its first startup.•Backup/UpgradeUpgrade / Backup allows

1CONTENTSINTRODUCTION ...3HARDWARE INSTALLATION ...

198. Restart your PCAfter the router has successfully rebooted, you must restart your PC if you have entered DNS information (see Step 4): the PC will

20In most cases, Plug and Play will automatically detect your network adapter and install any necessary drivers. However, if Plug and Play fails, the

21Adapter Setup1. From the taskbar, click the Start button (located at the lower left corner of your PC screen).2. Point to Settings, click Control Pa

224. From Select Network Component, click Protocol, and then click Add.5. In the Select Network Protocol window, select Microsoft as the Manufacturer.

23♦ SmartSwitch™ Router 250 Hardware SpecificationsLAN InterfacesOne Ethernet port, 10Base-T(twisted pair RJ45)LAN speed of 10 MbpsWAN InterfacesOne A

24Operating EnvironmentTemperature: 40°F to 105°F (5°C to 40°C)Humidity: 20%-80%, non-condensingPower RequirementsAC Voltage: 100 to 120 VAC, 220 to24

25♦ Front PanelThe front panel displays the activity of the SmartSwitch™Router 250.LED StatesINDICATOR DESCRIPTIONPWRGreen: Power is appliedOff: Power

26♦ Rear PanelThe rear panel contains all Ethernet, DSL, console, and power interfaces.10BASE-TThe 10Base-T Ethernet LAN interface. The router is conn

27ADSL-DMTConnection to the external telephone line interface.♦ConnectionsEthernet LAN ConnectionThe unit provides 10 Mbps Ethernet/IEEE 802.3 support

28♦ Port DescriptionsEthernet 10Base-T PortADSL-DMT PortPin Signal Name1 Twisted pair transmit +2 Twisted pair transmit -3 Twisted pair receive +4 Gro

2

29Console Port4 Tip or Line A5 Ring or Line B6 Not connected or Line B7 Not connected8 Not connectedPin Signal Name1 Receive data2 Request to send3 No

30 Part 15 CLASS B StatementSection 15.105(b) of the Code of Federal RegulationsNote:This equipment has been tested and found to comply with the limit

31CAUTION: Any changes or modifications not expressly approved by the party responsible for this device could void the user’s authority to operate thi

32Before you contact Technical Support, please have the following information ready:•Router model number•Router software version•Date of purchase•Type

33How to contact Technical Support in the U.S.Addresses / NumbersTelephone1-603-332-9400Monday-Friday; 8 A.M. - 8 P.M.Eastern TimeE-Mailsupport@ctron.

3♦ The SmartSwitch™ Router 250The SmartSwitch™ Router 250 provides Internet and Corporate access for telecommuters, home and remote office workers, an

4♦ This GuideThis guide describes the configuration process involved in setting up an ATM-based virtual circuit connection to a network service provid

5♦ Before You Begin...System requirements for Cabletron Quick Start •Windows 95, 98, NT 4.0, or Windows for Workgroups 3.11•Ethernet network interface

6Which network options should you use?•Bridging •IP Routing •Both Bridging and IP Routing♦Contents of the BoxYou should find the following items:•Smar

7♦ Instructions to Install the SmartSwitch™ Router 250 Hardware:1. Ensure that the Power Switch on the router is OFF. Connect the router to the AC pow

8♦ SmartSwitch™ Router 250 Installation DiagramThe following diagram shows the back panel of the SmartSwitch™ Router 250 and the location of jacks.