Cabletron Systems E2210 Guía de usuario

Solaris 7 (Intel Platform Edition)Device Configuration GuideSun Microsystems, Inc.901 San Antonio RoadPalo Alto, CA 94303U.S.A.Part No: 805–4854–10Octo

How to Obtain Technical SupportTo obtain technical support:Contact your Sun Software Support Provider.In North America, you can also call 1-800-786–76

IRQ Level:3, 6, 7, 9I/O Address:0xA20, 0xA24If there are multiple adapters installed, do notoverlap them.Auto 16/4 Token Ring adapters (ISA):IRQ Level

Auto 16/4 and Turbo 16/4 Token Ring adapters in ISA systems only: Run theLANAID program that comes with the adapter.2. Set up the Token Ring so that:T

Madge Smart 16/4 Token RingSolaris Device Driver:mtokDevice Type:Network (Token ring)Adapters:Madge Smart 16/4 AT Ringnode/Bridgenode,Smart 16/4 AT Pl

the MDGBOOT diskette shipped with your Ringnode. Refer to the documentationsupplied with the Ringnode for detailed instructions.When choosing hardware

Audio CardsAnalog Devices AD1848 andCompatible DevicesSolaris Device Driver:sbproDevice Type:AudioChips:Analog Devices AD1848, Compatible Devices (onc

Compaq Deskpro XL Business Audio with built-in AD1847 chipTurtle Beach Tropez card with CS4231 chipSome other 100 percent hardware-compatible devices

The sbpro driver automatically chooses an unused DMA channel and IRQ line forthe device.Note - The sbpro support for the AD1848 and compatibles uses o

Although the sbpro driver supports A-law encoding on AD1848 and compatibledevices, audiotool does not and produces an error message if you select A-la

Creative Labs Sound Blaster Pro, SoundBlaster Pro-2Solaris Device Driver:sbproDevice Type:AudioAdapters:Creative Labs Sound Blaster Pro,Sound Blaster

• IRQ Level: 2, 5, 7,10• I/O Address:0x220, 0x240• DMA Channel: 0, 1,3Known Problems and LimitationsThe ISA version IBM Token Ring and compatible adap

CHAPTER 1Configuring DevicesThis chapter describes how to use Solaris 7 Intel Platform Edition DeviceConfiguration Assistant software, manufacturers’ de

Creative Labs Sound Blaster 16, SoundBlaster AWE32, Sound Blaster Vibra 16Solaris Device Driver:sbproDevice Type:AudioAdapters:Creative Labs Sound Bla

Defaults are shown in this typeface.• IRQ Level: 2, 5,7,10• I/O Address:0x220, 0x240, 0x260, 0x280• 8-bit DMA Channel: 0, 1,3• 16-bit DMA Channel:5,6,

PC Card (PCMCIA) HardwarePC Card AdaptersSolaris Device Driver:pcicAdapters:Intel i82365SLVadem VG365, VG465, VG468, VG469Cirrus Logic PD6710, PD6720R

Address space At least 8 Kbytes are required with 4 Kbytes per socketin the 640K-1MB range (not necessarily contiguous); ifthere are three sockets, at

# touch /reconfigure# reboot4. Insert the PC Card adapter and turn on the machine.5. Do a second reboot so that the PC Card device driver begins runni

3Com EtherLink III (3C562, 3C589) PCCardsSolaris Device Driver:pcelxDevice Type:Network (Ethernet)Adapter:3Com EtherLink III 3C562 (network, modem),Et

2. Boot the system.3. Insert the 3Com EtherLink III PC Card device.Identifying an Unrecognized CardIf you insert a 3C562 or 3C589 card and it isn’t re

Note - This process is described in TCP/IP and Data CommunicationsAdministration Guide.Special FilesDevice naming in /dev follows standard LAN device

Modem and Serial PC Card DevicesSolaris Device Driver:pcserDevice Type:Modem and serial PC Card devices based on the8250, 16550, or compatible UART at

# prtconf -D...pcic, instance #0 (driver name: pcic)...pccard111.222 (driver not attached)3. If your device is not recognized “(driver not attached)”,

Identifying a Problem With an Existing Device1. Consult the manufacturer’s documentation and Device Reference Page, if thereis one. Ensure the device

3. To work properly with the Solaris operating environment, all devices must beaccounted for, even those the Solaris environment does not support. The

SRAM and DRAM PC Card DevicesSolaris Device Driver:pcramDevice Types:Static RAM (SRAM), Dynamic RAM (DRAM)Bus Type:PC CardNote - Flash RAM devices are

Identifying an Unrecognized DeviceIf you insert a memory device and it isn’t recognized (no special files created), usethe prtconf command.1. Become ro

Note - A device name can be specified either by a partition name (p#) or a slicename (s#), but not both.Using PC Card Memory DevicesSince the Solaris V

Viper 8260pA, SanDisk Flash, or AnyPC Card ATA DevicesSolaris Device Driver:pcataDevice Type:ATA PC CardAdapters:Viper 8260pASanDisk FlashOr any PC Ca

2. Boot the system.3. Insert the PC Card ATA device.Identifying an Unrecognized CardIf you insert a PC Card ATA device and it isn’t recognized (no spe

# newfs /dev/rdsk/c#d#s#To mount a ufs file system, type:# mount -F ufs /dev/dsk/c#d#s# /mntFor more information, see the newfs(1M) and mount(1M) man p

4. Go to the Device Tasks menu, select View/Edit Devices, and examine the list ofdevices provided to determine if the problem device conflicts with ano

The program should warn you if there is a conflict.3. When the scan is successful, go to the Boot Solaris menu and select a device toboot from.If you p

4. Boot the Solaris software.Unrecognized DevicesIssue What to DoHow a known ISA or EISA device canbe recognized by the ConfigurationAssistant software

AutobootingIssue What to DoHow to recover if your machine fails toautoboot.If you have a loopback serial cable betweenCOM1 and COM2 with autobooting e

PCI DevicesIssue What to DoHow to control the assignments ofIRQs to PCI devices.In the chipset configuration of the system, verifythat an IRQ is enable

Issue What to DoHow to configure an unrecognizedvideo display device manually.If hardware limitations or inadequate informationfrom the BIOS prevent pr

Connector TypesDevice Reference Pages specify the supported connector type where appropriate. Allnetwork devices are assumed to work at 10 Mbps only,

Copyright 1998 Sun Microsystems, Inc. 901 San Antonio Road, Palo Alto, California 94303-4900 U.S.A. All rights reserved.This product or document is pr

Postinstallation ConfigurationReplacing a Network CardIf you replace your network card with one that uses a different network driver (forexample, chang

CHAPTER 2Device Reference PagesThis chapter describes how to use Device Reference Pages to configure your x86based system to run in the Solaris operati

Third-party drivers are provided for the convenience of Solaris customers and aretested to ensure that they meet acceptable standards of operability.

Device Type Solaris Driver Name Where to Find Device Reference Pagesesa“Adaptec AHA-2740, 2742, 2740A, 2742A,2740T, 2742T, 2740AT, 2742AT, 2740W,2742W

Device Type Solaris Driver Name Where to Find Device Reference Pagesdpt“DPT PM2024, PM2044W, PM2044UW,PM2124, PM2124W, PM2144W, PM2144UWSCSI and PM322

Device Type Solaris Driver Name Where to Find Device Reference Pageselxl“3Com EtherLink XL (3C900,3C900-COMBO, 3C900B-COMBO,3C900B-TPC, 3C900B-TPO), F

Device Type Solaris Driver Name Where to Find Device Reference Pagessmce“SMC Elite32 (8033)” on page 83smceu“SMC Elite32C Ultra (8232)” on page 84smcf

Device Type Solaris Driver Name Where to Find Device Reference Pagespcser“Modem and Serial PC Card Devices” onpage 108pcram“SRAM and DRAM PC Card Devi

Disk InterfaceIDE/Enhanced IDE Disk Controller(Including ATAPI CD-ROM)Solaris Device Driver:ataDevice Type:Hard disk or CD-ROM controllerSupported Con

• IRQ Level: 15• I/O Address: 0x170If an IDE CD-ROM drive is installed, the system BIOS parameter for that deviceshould be:• Drive Type: Not installed

ContentsPreface ix1. Configuring Devices 1Identifying and Correcting Problems 1ISA Devices 1PC Card Devices 4Unrecognized Devices 5Autobooting 6Using M

Comment out the following line in the file /etc/vold.conf to prevent voldfrom hanging the controller:# use cdrom drive /dev/rdsk/c*s2 dev_cdrom.so cdro

SCSI Host Bus AdaptersAdaptec AHA-1510A, 1520A, 1522A,1530P, 1532P HBAsSolaris Device Driver:aicDevice Type:SCSIAdapters:Adaptec AHA-1510A, AHA-1520A,

Known Problems and LimitationsThe Adaptec AHA-1510A adapter cannot be a primary (boot) disk controller since ithas no BIOS. Boot from a disk attached

Creative Labs Sound Blaster 16 SCSI-2InterfaceSolaris Device Driver:aicDevice Type:SCSIAdapter:Creative Labs Sound Blaster 16 SCSI-2Bus Type:ISAPrecon

The SCSI interface on the Sound Blaster 16 SCSI-2 audio card cannot be used as aprimary (boot) disk controller since it has no BIOS. The system must b

Adaptec AHA-1540B, 1542B, 1542C,1542CF, 1542CP HBAsSolaris Device Driver:ahaDevice Type:SCSIAdapters:Adaptec AHA-1540B, AHA-1542B, AHA-1542C,AHA-1542C

• Synchronous Negotiation: Disabled for each CD-ROM drive target• Support for More Than Two DOSDrives:Disabled• Dynamically Scan SCSI Bus for BIOSDevi

Adaptec AHA-1740, 1742A HBAsSolaris Device Driver:ehaDevice Type:SCSIAdapters:Adaptec AHA-1740, AHA-1742ABus Type:EISAPreconfiguration InformationSuppo

Adaptec AHA-2740, 2742, 2740A, 2742A,2740T, 2742T, 2740AT, 2742AT, 2740W,2742W, 2840A, 2842A, 2840VL, 2842VLHBAsSolaris Device Driver:esaDevice Type:S

For example, set the tape drive’s SCSI ID to 7 using jumpers or an external switch.Then set the AHA-274x SCSI ID to 6 using the ECU. (Use the configura

2. Device Reference Pages 11Third-Party Drivers 11Using Device Reference Pages 12Disk Interface 18IDE/Enhanced IDE Disk Controller (Including ATAPI CD

The BIOS base address is selected from a range of choices on themanufacturer-supplied configuration utility. Common addresses for the AIC-7770controlle

Adaptec AHA-2940, 2940AU, 2940W,2940U, 2940U Dual, 2940UW, 2940UWDual, 2944W, 2944UW, 3940, 3940W,3940U, 3940UW, 3940AU, 3940AUW,3940AUWD, 3944AUWD HB

to “To ISA Legacy IRQs”. A similar workaround may apply to other motherboardswith problems supporting channel B.Another possible workaround is noted o

For older disk drives, tape drives, and most CD-ROM devices, make sure themaximum SCSI data transfer speed is set to 5.0 Mbps.Enable support for disks

AMD PCscsi, PCscsi II, PCnet-SCSI andQLogic QLA510 HBAsSolaris Device Driver:pcscsiDevice Type:SCSIAdapter:QLogic QLA510Chips:AMD 53C974 (PCscsi), 53C

BusLogic (Mylex) BT-742A, BT-746C,BT-747C, BT-747S, BT-757C, BT-757S,BT-542B, BT-545C, BT-545S, BT-440C,BT-445C, BT-445S HBAsSolaris Device Driver:blo

Configuration ProcedureModel names ending in “C” only: Run the manufacturer’s AutoSCSI configurationutility and check the termination and that the Advan

BusLogic (Mylex) BT-946C, BT-948,BT-956C, BT-956CD, BT-958, BT-958DHBAsSolaris Device Driver:blogicDevice Type:SCSIAdapters:BusLogic (Mylex) BT-946C,

Note - I/O addresses are dynamically configured for BT-946C Rev. C PCI adapters.Known Problems and LimitationsUsing an I/O address of 0x330 causes the

Ensure the Advanced option “BIOS Support for > 2 Drives (DOS 5.0 or above)” isset to No.Configure the IRQ and BIOS address values manually if your P

Preconfiguration Information 35Configuration Procedure 36BusLogic (Mylex) BT-946C, BT-948, BT-956C, BT-956CD, BT-958, BT-958D HBAs 37Preconfiguration Inf

Compaq 32-Bit Fast SCSI-2 ControllersSolaris Device Driver:ncrsDevice Type:SCSI-2Adapters:Compaq Integrated 32-Bit Fast-SCSI-2/P53C810 chipProSignia 3

Compaq 32-Bit Fast Wide SCSI-2, WideUltra SCSI, Dual Channel Wide UltraSCSI-3 ControllersSolaris Device Driver:cpqncrDevice Type:SCSIAdapters:Compaq 3

1 - Enabledalrm_msg_enable: This property enables or disables Alarm messages due tofaults in the Compaq Storage system connected to the 825, 875, or 8

DPT PM2011, PM2021, PM2041W,PM3021 HBAsSolaris Device Driver:dptDevice Type:SCSIAdapters:DPT PM2011, PM2021, PM2041W, PM3021Bus Type:ISAPreconfiguratio

Use edge-triggered interrupts on the PM2011.The PM2041W adapter’s SmartROM must be upgraded to at least version 3DL inplace of 3D0. The BIOS on adapte

DPT PM2012B HBASolaris Device Driver:dptDevice Type:SCSIAdapter:DPT PM2012BBus Type:EISAPreconfiguration InformationSupported Settings• IRQ Level: Any

a. Type DPTFMT and press Enter.b. Press Enter to begin, and again to continue.c. Press <F3> to enter SCSI ID 0 and LUN 0, and press <F3> t

Symbios Logic (also NCR) 53C810,53C810A, 53C815, 53C820, 53C825,53C825A, 53C860, 53C875, 53C875J,53C876, 53C895 HBAsSolaris Device Driver:ncrsDevice T

Do not attempt to connect wide targets to the 53C810, 53C815, and 53C860 using awide to narrow converter. These configurations are not supported.If you

Trantor T348 MiniSCSI Plus ParallelHBAsSolaris Device Driver:trantorDevice Type:SCSIAdapter:Trantor T348Preconfiguration InformationThe T348 ends in a

DPT PM2022, PM2042W, PM2122, PM2142W SCSI and PM3222, PM3222UW,PM3332UW SCSI RAID HBAs 55Preconfiguration Information 55Configuration Procedure 56DPT PM

printer or Ethernet adapter, shut down the Solaris operating environment and turnoff the computer and any SCSI devices attached to the T348.With the p

SCSI Disk Arrays/RAID ControllersAmerican Megatrends MegaRAID 428SCSI RAID ControllerSolaris Device Driver:megaDevice Type:SCSI RAIDAdapter:American M

name="sd" class="scsi"target=0 lun=1;name="sd" class="scsi"target=0 lun=2;4. Reboot.After the system reboots,

Compaq SMART Array ControllerSolaris Device Driver:csaDevice Type:Disk ArrayAdapter:Compaq SMART Array ControllerBus Type:EISASystems Supported:Intern

Compaq SMART-2, SMART-2DH,SMART-2SL Array ControllersSolaris Device Driver:smartiiDevice Type:Disk ArrayAdapters:Compaq SMART-2, SMART-2DH, SMART-2SLA

DPT PM2022, PM2042W, PM2122,PM2142W SCSI and PM3222,PM3222UW, PM3332UW SCSI RAIDHBAsSolaris Device Driver:dptDevice Types:SCSI, SCSI RAIDAdapters:DPT

Known Problems and LimitationsTo prevent system hangs caused by improper IDE emulation, the EISA!DPTA410.CFG file should be at least version 6E5. If it

DPT PM2024, PM2044W, PM2044UW,PM2124, PM2124W, PM2144W,PM2144UW SCSI and PM3224,PM3224W, PM3334W, PM3334UW SCSIRAID HBAsSolaris Device Driver:dptDevic

Supported Settings• I/O Address: Auto58 Solaris 7 (Intel Platform Edition) Device Configuration Guide ♦ October 1998

IBM PC ServeRAID SCSI HBASolaris Device Driver:chsDevice Type:SCSI RAIDAdapter:IBM PC ServeRAIDBus Type:PCIPreconfiguration InformationKnown Problems a

Intel EtherExpress 16, 16C, 16TP (82586) 75Preconfiguration Information 75Intel EtherExpress Flash32 (82596) 76Preconfiguration Information 76Intel Ethe

Mylex DAC960PD-Ultra, DAC960PD/DAC960P, DAC960PG, DAC960PJ,DAC960PL, DAC960E ControllersSolaris Device Driver:mlxDevice Type:SCSI-2 RAIDAdapters:Mylex

Therefore, even though a standby drive is physically connected, the system deniesaccess to it so no data can be accidentally lost.Other than the stand

Ethernet Network Adapters3Com EtherLink (3C509), EtherLink III(3C509B), EtherLink III Bus Master(3C590, 3C592, 3C595-TX, 3C597-TX)Solaris Device Drive

3Com EtherLink XL (3C900,3C900-COMBO, 3C900B-COMBO,3C900B-TPC, 3C900B-TPO), FastEtherLink XL (3C905-TX, 3C905-T4,3C905B-TX, 3C905B-T4)Solaris Device D

AMD PCnet Ethernet (PCnet-ISA,PCnet-PCI, PCnet-PCI II, PCnet-Fast),Allied Telesyn AT-1500, MicrodyneNE2500plus, Cabletron E-2210Solaris Device Driver:

Compaq NetFlex-2 DualPort ENET,NetFlex-2 ENET-TR ControllersSolaris Device Driver:nfeDevice Type:Network (Ethernet and token ring)Adapters:Compaq NetF

The default setting (DB-9) on the NetFlex-2 ENET-TR needs to be changed.2. Compaq NetFlex-2 ENET-TR card only: Configure this card to use a 10-Mbpsdata

Compaq NetFlex-3, NetelligentControllersSolaris Device Driver:cnftDevice Type:Network (Ethernet)Adapters:Compaq NetFlex-3/E, NetFlex-3/P and:10BASE-T

Preconfiguration InformationInsert a 10BASE-T UTP, 10/100BASE-TX UTP, 100BASE-FX, or 100VG-AnyLANUTP module into the NetFlex-3 PCI or EISA controller b

2. Modify the driver configuration file/platform/i86pc/kernel/drv/cnft.conf.This file specifies the valid configurable parameters for the driver:duplex_mod

Preconfiguration Information 92Configuration Procedure 92Audio Cards 94Analog Devices AD1848 and Compatible Devices 94Compatible Device Information 94Pr

DEC 21040, 21041, 21140, 21142, 21143EthernetSolaris Device Driver:dnetDevice Type:Network (Ethernet)Adapters:DEC 21040, 21041, 21140, 21142, 21143Bus

Name/Model Part/Version Chip21xxx10 MBMedia100 MBMediaNotesCogent EM110TX 110001-03 14 140AC T XCogent EM400 QUAD 400001-00 01 140 XCogent EM400 QUAD

Name/Model Part/Version Chip21xxx10 MBMedia100 MBMediaNotesLinksys LNE100TX 8EFPCI01..B1-3 140AC T X 7NetGear FA310TX-C2 140AE T XNetGear FA310TX-C6 1

Name/Model Part/Version Chip21xxx10 MBMedia100 MBMediaNotesZnyx ZX346 QUAD SA0026 X1 140AC T X AZnyx ZX348 DUAL SA0028 X2 140AC T X B10 MB Media Codes

The dnet driver incorrectly counts carrier lost or no carrier errors while infull-duplex mode. There is no carrier signal present when in full-duplex

Intel EtherExpress 16, 16C, 16TP (82586)Solaris Device Driver:ieeDevice Type:Network (Ethernet)Adapters:Intel EtherExpress 16, 16C, 16TP (82586)Bus Ty

Intel EtherExpress Flash32 (82596)Solaris Device Driver:ieefDevice Type:Network (Ethernet)Adapter:Intel EtherExpress Flash32 (82596)Bus Type:EISAConne

Intel EtherExpress PRO (82595),EtherExpress PRO/10+ (82595FX)Solaris Device Driver:eeproDevice Type:Network (Ethernet)Adapters:Intel EtherExpress PRO

Intel EtherExpress PRO/100 (82556)Solaris Device Driver:ieefDevice Type:Network (Ethernet)Adapter:Intel EtherExpress PRO/100 (82556)Bus Types:EISA, PC

Novell NE2000, NE2000plus Ethernet,and CompatiblesSolaris Device Driver:neiDevice Type:Network (Ethernet)Adapters:Novell NE2000, NE2000plus, Compatibl

PrefaceThis document provides information about x86 hardware devices that are supportedin the SolarisTM7 computing environment.Note - The term “x86” r

• IRQ Level: 3, 4, 5, 9, 10, 11, 12, 14, 15• I/O Address: 0x200, 0x220, 0x240, 0x260, 0x280, 0x2C0, 0x300, 0x320,0x340, 0x360NE2000plus:• IRQ Level: 3

For NE2000 compatibles that do not operate at all combinations of I/O addressand IRQ settings, use the default values of IRQ 3 and I/O address 0x300.N

Novell NE3200 EthernetSolaris Device Driver:neeDevice Type:Network (Ethernet)Adapter:Novell NE3200Bus Type:EISAConnectors:RJ-45, BNC, AUIPreconfigurati

SMC Elite32 (8033)Solaris Device Driver:smceDevice Type:Network (Ethernet)Adapter:SMC Elite32 (8033)Bus Type:EISAConnectors:One board type has an AUI

SMC Elite32C Ultra (8232)Solaris Device Driver:smceuDevice Type:Network (Ethernet)Adapter:SMC Elite32C Ultra (8232)Bus Type:EISAConnectors:RJ-45, AUI,

SMC Ether 10/100 (9232)Solaris Device Driver:smcfDevice Type:Network (Ethernet)Adapter:SMC Ether 10/100 (9232)Bus Type:EISAConnector:RJ-45Preconfigurat

SMC EtherEZ (8416), EtherCard Elite16Ultra (8216), EtherCard PLUS Elite(8013), EtherCard PLUS Elite 16 (8013),EtherCard PLUS (8003), EtherCard Elite32

I/O Address IRQ Base Memory Address (Board RAM)0x260 5 0xE00000x380 7 0xD4000Known Problems and LimitationsThe boards will only work in memory-mapped

Xircom Pocket Ethernet (PE3 and PE2)Solaris Device Driver:peDevice Type:Network (Ethernet)Adapters:Xircom Pocket Ethernet (PE2 and PE3)Port:Attach to

Token Ring Network AdaptersIBM 16/4, Auto 16/4, Turbo 16/4 TokenRing and Compatible AdaptersSolaris Device Driver:trDevice Type:Network (Token Ring)Ad