Cabletron Systems SmartSwitch Manual de usuario Pagina 182
- Pagina / 338
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 11: Routing Policy Configuration Guide
182 SmartSwitch Router User Reference Manual
Creating an Aggregate Destination
To create an aggregate destination, enter the following command in Configure mode:
Creating an Aggregate Source
To create an aggregate source, enter the following command in Configure mode:
Examples of Import Policies
Example 1: Importing from RIP
The importation of RIP routes may be controlled by any of protocol, source interface, or
source gateway. If more than one is specified, they are processed from most general
(protocol) to most specific (gateway).
RIP does not support the use of preference to choose between routes of the same protocol.
That is left to the protocol metrics.
For all examples in this section, refer to the configuration shown in Figure 17 on page 183.
Create an aggregate
destination.
ip-router policy create aggr-gen-dest <name>
network
<ipAddr-mask>
Create an aggregate source. ip-router policy create aggr-gen-source <name>
protocol
<protocol-name>
- SmartSwitch Router 1
- User Reference Manual 1
- Industry Canada Notice 3
- VCCI Notice 3
- CABLETRON SYSTEMS, INC 4
- PROGRAM LICENSE AGREEMENT 4
- CABLETRON SYSTEMS LIMITED 8
- SAFETY INFORMATION 10
- DECLARATION OF CONFORMITY 11
- ADDENDUM 11
- Contents 13
- About This Manual 25
- Who Should Read This Manual? 25
- How to Use This Manual 25
- Related Documentation 27
- Chapter 1 29
- SSR Product 29
- Overview 29
- Supported Routing Protocols 31
- Basic Line Editing Commands 33
- Access Modes 33
- User Mode 34
- Enable Mode 35
- Exit Enable mode 36
- Configure Mode 37
- Boot PROM Mode 38
- Boot and System Image 39
- Configuration Files 39
- Loading System Image Software 40
- Loading Boot PROM Software 41
- Managing the SSR 43
- Setting the SSR Name 44
- Setting SSR Date and Time 44
- Configuring NTP 44
- Configuring the SSR CLI 45
- Configuring SNMP Services 45
- Configuring DNS 45
- Configuring Logging 46
- Monitoring Configuration 47
- Chapter 2 49
- Hot Swapping 49
- Line Cards and 49
- Control Modules 49
- Deactivating the Line Card 50
- Removing the Line Card 50
- Removing the Control Module 52
- Installing the Control Module 53
- Offline LED 54
- Hot Swap Button 54
- Chapter 3 55
- Bridging 55
- VLAN Overview 56
- SSR VLAN Support 58
- Configuring Spanning Tree 61
- Configuring VLAN Trunk Ports 65
- Monitoring Bridging 66
- Chapter 4 69
- SmartTRUNK 69
- Configuring SmartTRUNKs 70
- Monitoring SmartTRUNKs 71
- Example Configurations 72
- Chapter 5 75
- Configuring DHCP 76
- Updating the Lease Database 78
- Monitoring the DHCP Server 78
- DHCP Configuration Examples 79
- Configuring Secondary Subnets 80
- Interacting with Relay Agents 82
- Chapter 6 85
- IP Routing 85
- IP Routing Protocols 86
- Configuring DNS Parameters 90
- Configuring IP Helper 91
- Configuring Direct Broadcast 91
- Configuring Router Discovery 92
- Chapter 7 95
- Basic VRRP Configuration 96
- Symmetrical Configuration 97
- Multi-Backup Configuration 99
- 10.0.0.1/16 100
- 10.0.0.2/16 100
- 10.0.0.3/16 100
- Additional Configuration 103
- Monitoring VRRP 105
- VRRP Configuration Notes 106
- Chapter 8 109
- RIP Configuration 109
- Enabling and Disabling RIP 110
- Configuring RIP Interfaces 110
- Configuring RIP Parameters 110
- Monitoring RIP 112
- Configuration Example 113
- ! Change default metric-out 114
- Chapter 9 115
- Configuration 115
- Configuring OSPF 116
- Configuring an OSPF Area 118
- Creating Virtual Links 119
- Advertisements 120
- Monitoring OSPF 121
- OSPF Configuration Examples 122
- ASE routes into RIP 125
- A r e a 140.1.0.0 126
- (RIP V2) 126
- Chapter 10 127
- BGP Configuration 127
- Basic BGP Tasks 128
- Setting the Router ID 129
- Configuring a BGP Peer Group 129
- Starting BGP 131
- BGP Configuration Examples 134
- BGP Peering Session Example 135
- IBGP Configuration Example 137
- IBGP Internal Group Example 141
- 17.122.128.2/24 142
- 17.122.128.1/24 142
- Community Attribute Example 147
- Physical Link 149
- Peering Relationship 149
- Information Flow 149
- Local_Pref Attribute Example 154
- EBGP Aggregation Example 158
- Route Reflection Example 159
- 192.68.222.1 160
- 192.68.20.2 160
- 192.68.20.1 160
- 172.16.30.2 160
- Chapter 11 163
- Routing Policy 163
- Preference 164
- Import Policies 165
- Export Policies 166
- Specifying a Route Filter 167
- Aggregates and Generates 168
- Authentication 170
- Redistributing Static Routes 172
- Redistributing RIP into RIP 173
- Redistributing RIP into OSPF 173
- Redistributing OSPF to RIP 173
- Creating an Export Source 179
- Creating an Import Source 180
- Creating a Route Filter 180
- Creating an Aggregate Route 180
- Creating an Aggregate Source 182
- Examples of Import Policies 182
- Examples of Export Policies 189
- Chapter 12 199
- Multicast Routing 199
- DVMRP Overview 200
- Configuring IGMP 201
- Configuring DVMRP 202
- Configuring DVMRP Parameters 203
- Configuring a DVMRP Tunnel 204
- Monitoring IGMP & DVMRP 205
- Configuration Examples 206
- Chapter 13 209
- IP Policy-Based 209
- Forwarding 209
- Configuring IP Policies 210
- Firewall Load Balancing 218
- Monitoring IP Policies 219
- Chapter 14 223
- Network Address 223
- Translation 223
- Configuring NAT 224
- Managing Dynamic Bindings 225
- NAT and FTP 226
- Monitoring NAT 226
- Dynamic Configuration 228
- Chapter 15 233
- Web Hosting 233
- Load Balancing 234
- Setting Server Status 235
- Load Balancing and FTP 236
- Destination 239
- Server IP 239
- TCP Port 239
- Web Caching 240
- Other Configurations 242
- Monitoring Web-Caching 243
- Chapter 16 245
- IPX Routing 245
- Configuring IPX RIP & SAP 247
- Configuring IPX Routing 249
- Monitoring an IPX Network 252
- • Adds a SAP access list 253
- • Adds a GNS access list 253
- Chapter 17 255
- Access Control List 255
- ACL Basics 256
- How ACL Rules are Evaluated 257
- Implicit Deny Rule 258
- Creating and Modifying ACLs 260
- Using ACLs 262
- Applying ACLs to Services 263
- Using ACLs as Profiles 263
- Enabling ACL Logging 268
- Monitoring ACLs 269
- Chapter 18 271
- Security 271
- Configuring RADIUS 272
- Configuring TACACS 273
- Configuring TACACS Plus 274
- Layer-2 Security Filters 275
- Layer-2 Filter Examples 279
- Chapter 19 283
- QoS Configuration 283
- Precedence for Layer-3 Flows 284
- SSR Queuing Policies 285
- Configuring Layer-2 QoS 285
- Configuring IP QoS Policies 286
- Configuring IPX QoS Policies 287
- ToS Rewrite 288
- Monitoring QoS 291
- Limiting Traffic Rate 291
- Example Configuration 292
- Chapter 20 295
- Performance 295
- Monitoring Guide 295
- Monitoring Broadcast Traffic 297
- Chapter 21 299
- RMON Groups 301
- Control Tables 303
- Using RMON 304
- Configuring RMON Groups 305
- Displaying RMON Information 308
- RMON CLI Filters 309
- Troubleshooting RMON 311
- Allocating Memory to RMON 313
- Chapter 22 315
- Configuring WAN Interfaces 316
- Forcing Bridged Encapsulation 318
- Packet Compression 318
- Packet Encryption 320
- WAN Quality of Service 320
- Frame Relay Overview 322
- Configuring PPP Interfaces 327
- Monitoring PPP WAN Ports 330
- PPP Port Configuration 330
- WAN Configuration Examples 332
- Router R1 Configuration File 334
- Router R2 Configuration File 334
- Router R3 Configuration File 335
- Router R4 Configuration File 335
- Router R5 Configuration File 336
- Router R6 Configuration File 336
Relacionado con productos y manuales para Redes Cabletron Systems SmartSwitch
Redes Cabletron Systems SSIM-R8-02 Especificaciones
(394 paginas)
(394 paginas)
Redes Cabletron Systems WPIM-RT1 Especificaciones
(190 paginas)
(190 paginas)
Redes Cabletron Systems BRIM-E6 Especificaciones
(40 paginas)
(40 paginas)
Redes Cabletron Systems ELS10-26 Manual de usuario
(19 paginas)
(19 paginas)
Redes Cabletron Systems T2015 Especificaciones
(228 paginas)
(228 paginas)
Redes Cabletron Systems SSIM-R8-02 Manual de usuario
(16 paginas)
(16 paginas)
Redes Cabletron Systems ETWMIM Especificaciones
(262 paginas)
(262 paginas)
Redes Cabletron Systems BRIM-E6 Especificaciones
(45 paginas)
(45 paginas)
Redes Cabletron Systems BRIM-E6 Especificaciones
(39 paginas)
(39 paginas)
Redes Cabletron Systems E2100 Manual de usuario
(396 paginas)
(396 paginas)
Redes Cabletron Systems HSIM-W6 Guía de instalación
(60 paginas)
(60 paginas)
Redes Cabletron Systems HSIM-FE6 Guía de usuario
(42 paginas)
(42 paginas)
Redes Cabletron Systems CSX400-DC Guía de usuario
(275 paginas)
(275 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.092 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales