Cabletron Systems CSX1200 Especificaciones Pagina 103
- Pagina / 106
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Workgroup Remote Access Switch 103
A
PPLE
T
ALK
R
OUTING
N
ETWORK
Configure the CyberSWITCH
CONFIGURING DEVICE SITE2’S AUTHENTICATION INFORMATION
At the Device Table Menu, select Authentication. You may then enter the authentication information
needed for this device. The information needed for each device depends on the device type.
For device SITE2, because we will be configuring CHAP security, we will configure a CHAP secret
(ikcd98s). After the secret has been entered, the Device Authentication Menu will appear as follows:
Again, return to the Device Table Menu.
C
ONFIGURING DEVICE SITE2’S APPLETALK INFORMATION
To begin the configuration of device SITE2’s AppleTalk information, select AppleTalk from the
Device Table menu. A menu will then be displayed with preconfigured default values. as shown
below:
To complete the AppleTalk configuration for device SITE2:
• Select AppleTalk Address. Because this device is over an unnumbered link, enter 0.0 for the Ap-
pleTalk address.
• Select AppleTalk Routing. Follow the on-screen instructions to enable AppleTalk routing for
SITE2.
• Select Make calls for AppleTalk Data. Follow the on-screen instructions to enable making calls for
AppleTalk data.
Device Authentication Menu: (Device = "SITE2")
PPP:
1) PAP Password ""
2) CHAP Secret "ikcd98s"
3) Outbound Authentication ENABLED
4) User Level Authentication DISABLED
IP Host (RFC 1294):
5) IP Host Id ""
HDLC Bridge:
6) Bridge Ethernet Address ""
7) Bridge Password ""
ISDN:
8) Calling Line Id(s) ""
Select function from above or <RET> for previous menu:
Device AppleTalk Menu: (Device = "SITE2")
1) AppleTalk Address None
2) AppleTalk Routing DISABLED
3) Make calls for AppleTalk data DISABLED
4) AppleTalk Routing Protocol None
Select function from above or <RET> for previous menu:
- EXAMPLE NETWORKS 1
- VIRUS DISCLAIMER 2
- TRADEMARKS 3
- COPYRIGHTS 3
- FCC NOTICE 3
- DOC NOTICE 4
- VCCI NOTICE 4
- CONTENTS 5
- IPX Routing Network 77 6
- Index 106 7
- RESOURCES 10
- SYSTEM DETAILS 10
- BRIDGING 11
- IP ROUTING 11
- CONFIGURE THE CYBERSWITCH 12
- SAVE CONFIGURATION FILES 15
- OVERVIEW 17
- INITIAL INSTALLATION STEPS 17
- NETWORK TOPOLOGY 18
- SYSTEM DETAILS 19
- DEVICE INFORMATION 20
- San Fran 29
- CONFIGURING THE SECURITY 40
- USINESS ASSUMPTIONS 45
- ETWORK TOPOLOGY 46
- NETWORK TOPOLOGY 59
- CONFIGURE SITE1 65
- Configure SITE1 67
- CONFIGURE SITE2 74
- IPX ROUTING 84
- CONFIGURE DEVICES 85
- <RET> 86
- CONFIGURE SYSTEM OPTIONS 87
- <Y> 90
- CONFIGURE THE REMOTE DEVICES 92
- APPLETALK ROUTING 96
- ONFIGURING DEVICE INFORMATION 101
- Configure the CyberSWITCH 103
- VERIFY THE INSTALLATION 105
Relacionado con productos y manuales para Redes Cabletron Systems CSX1200
Redes Cabletron Systems SEHI100TX-22 Guía de usuario
(88 paginas)
(88 paginas)
Redes Cabletron Systems EFDMIM Guía de usuario
(36 paginas)
(36 paginas)
Redes Cabletron Systems 9F106-01 Especificaciones
(74 paginas)
(74 paginas)
Redes Cabletron Systems CSX400-DC Manual de usuario
(36 paginas)
(36 paginas)
Redes Cabletron Systems W85 Guía de usuario
(60 paginas)
(60 paginas)
Redes Cabletron Systems CBUPRI/E1 Especificaciones
(67 paginas)
(67 paginas)
Redes Cabletron Systems CSX7000 Especificaciones
(125 paginas)
(125 paginas)
Redes Cabletron Systems BRIM-WT1 Guía de instalación
(73 paginas)
(73 paginas)
Redes Cabletron Systems E2210 Manual de usuario
(21 paginas)
(21 paginas)
Redes Cabletron Systems 9F106-01 Guía de usuario
(26 paginas)
(26 paginas)
Redes Cabletron Systems BRIM-E100 Guía de usuario
(42 paginas)
(42 paginas)
Redes Cabletron Systems DLE52-MA Guía de usuario
(50 paginas)
(50 paginas)
Philips EasyStar Adaptador Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Für Zuhause Philips EasyStar Adaptador.
Wir stellen 1 PDF-Handbücher Philips EasyStar Adaptador zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Comentarios a estos manuales