Cabletron Systems 9C706 Guía de instalación

9031993-02 SmartSwitch 9000-6 Slot9 C106 and 9C706 ChassisSetup and Installation Guide

Introduction1-2 The Backplane The 9C106 SmartSwitch 9000-6 Slot chassis provides six distinct backplane buses, and the 9C706 provides an additional s

1-3Introduction System Management Bus 10 The System Management Bus 10, or SMB-10, performs similar functions to those of the SMB-1 previously discuss

Introduction1-4 Support for All SmartSwitch 9000 Interface Modules The chassis is designed to offer the same networking capabilities as Cabletron Sys

1-5Introduction FeaturesThermal Overload Protection A thermal shutdown circuit is included within the 9C206-1 power supply. This circuit protects the

Introduction1-6 Figure 1-3. The 9C306 System MonitorSTATUSCOM1COM2EPIMLNKEPIM-TSM9C306

1-7Introduction FeaturesOut-of-Band Management Out-of-band management refers to managing the SmartSwitch 9000-6 Slot via a Local Management (LM) conn

Introduction1-8 Chapter 1, Introduction , provides an overview of the 9C106 and 9C706 chassis, provides a list of related documentation., and detail

1-9Introduction Getting Help For additional support related to this device or document, contact Cabletron Systems using one of the following methods:

Introduction1-10

2-1 Chapter 2 SmartSwitch 9000-6 Slot Chassis Installation This chapter provides guidelines for choosing a site to install the SmartSwitch 9000-6 Slo

SmartSwitch 9000-6 Slot Chassis Installation2-2 ¥ A standard 3-prong power receptacle must be located within 6 feet of the system. One circuit is rec

2-3SmartSwitch 9000-6 Slot Chassis Installation Rack Mounting the SmartSwitch 9000-6 Slot ChassisThe chassis can be mounted in a standard 19-inch equ

SmartSwitch 9000-6 Slot Chassis Installation2-4Figure 2-1. Rack Mounting the ChassisFAN9C406

2-5SmartSwitch 9000-6 Slot Chassis InstallationInstalling a Power SupplyAt least one power supply must be installed on the front of the SmartSwitch 90

SmartSwitch 9000-6 Slot Chassis Installation2-6c. Firmly plug the power supply into the corresponding connector on the back of the chassis by pushing

2-7SmartSwitch 9000-6 Slot Chassis InstallationInstalling the 9C306 System Monitor The 9C306 System Monitor is installed in the slot marked SM on the

SmartSwitch 9000-6 Slot Chassis Installation2-8Figure 2-3. Installing SmartSwitch 9000-6 Slot ModulesInstalling a Fan ModuleThe Fan module can only be

2-9SmartSwitch 9000-6 Slot Chassis Installation2. Remove the Fan Module from the protective plastic bag. (Save the bag in the event the unit must be r

SmartSwitch 9000-6 Slot Chassis Installation2-10Installing SmartSwitch 9000-6 Slot Interface ModulesSmartSwitch 9000 Interface Modules can be installe

2-11SmartSwitch 9000-6 Slot Chassis InstallationPowering Up the SmartSwitch 9000-6 Slot ChassisPower up the SmartSwitch 9000-6 Slot chassis by followi

i Notice Cabletron Systems reserves the right to make changes in speciÞcations and other information contained in this document without prior notice.

SmartSwitch 9000-6 Slot Chassis Installation2-12

3-1Chapter 39C206-1 Power Supply OperationThis chapter describes the operation of the SmartSwitch 9000-6 Slot chassis power supply. The chapter also d

9C206-1 Power Supply Operation3-2Figure 3-1. 9C206-1 Power Supply LANVIEW LEDsPWR Status LEDThe PWR Status LED indicates the input and output status o

3-39C206-1 Power Supply OperationPower Supply Level Indicator LEDThe Power Supply Level Indicator LED indicates the percentage of the power supply loa

9C206-1 Power Supply Operation3-4

4-1Chapter 4SpecificationsEnvironmentOperating Temperature:5¡C to 40¡C (41¡F to 104¡F)Storage Temperature:-30¡C to 73¡C (-22¡F to 164¡F)Operating Relat

Specifications4-29C706 SmartSwitch 9000-6 Slot ChassisDimensions66 H x 43.2 W x 40.6 D centimeters(26 H x 17 W x 16 D inches)WeightUnit: 11.36 kilogra

A-1Appendix ASmartSwitch 9000-6 Slot ChassisSecurity BarsThe SmartSwitch 9000-6 Slot chassis is equipped with two security bars that prevent the unaut

SmartSwitch 9000-6 Slot Chassis Security BarsA-24. To install the top security bar, orient the bar with the securing tabs facing up and toward the cha

A-3Removing Security BarsFigure A-2. Security Bar InstallationRemoving Security BarsThe security bars should remain in place while the SmartSwitch 900

Noticeii FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not

SmartSwitch 9000-6 Slot Chassis Security BarsA-4

iiiNotice DECLARATION OF CONFORMITY Application of Council Directive(s): 89/336/EEC73/23/EEC ManufacturerÕs Name: Cabletron Systems, Inc. Manufacture

Noticeiv

v Contents Chapter 1 Introduction SmartSwitch 9000-6 Slot 9C106 Overview ... 1-19C106 Ch

Contentsvi Appendix A SmartSwitch 9000-6 Slot ChassisSecurity Bars Installing the Security Bars .....

1-1 Chapter 1 Introduction Welcome to the Cabletron Systems SmartSwitch 9000-6 Slot 9C106 and 9C706 Chassis Setup and Installation Guide . This manu