Cabletron Systems 9000 Guía de usuario

903number SmartSwitch 90009F426-03User’s Guide

Contentsviii Appendix A FPIM Specifications FPIM-00 and FPIM-01...

1-1 Chapter 1 Introduction The 9F426-03 FDDI SmartSwitch ® Module, shown in Figure 1-1, is a four port switch module with three front panel FDDI int

Introduction1-2 Cabletron enterprise MIBs. In addition, the front panel provides LEDs for FDDI link status per port, as well as transmit and receive

1-3Introduction Figure 1-1. The 9F426-03 ModuleSMB CPUINB9F426-03FDDI

Introduction1-4 Related Manuals The manuals listed below should be used to supplement the procedures and technical data contained in this manual.Smar

2-1 Chapter 2 Installing the SmartSwitch 9000 Module This module uses FPIMs for the front panel connections. They are not shipped with the module and

Installing the SmartSwitch 9000 Module2-2 Figure 2-1. Installing an FPIM User Accessible Components Figure 2-2 shows the various components that are

2-3Installing the SmartSwitch 9000 Module Figure 2-2. User Accessible Components An eight-position DIP switch is located on the module card as shown

Installing the SmartSwitch 9000 Module2-4 See the Cautions at the end of this table. Table 2-1. Function of DIP Switch Switch Function Description8

2-5Installing the SmartSwitch 9000 Module Installing the Module into the SmartSwitch 9000 Chassis To install the SmartSwitch 9000 module, follow the

Installing the SmartSwitch 9000 Module2-6 Figure 2-3. Installing the 9F426-03 ModuleMetal Back-PanelModule GuidesModuleJack for ESDWrist StrapPlastic

2-7Installing the SmartSwitch 9000 Module The Reset Switch The Reset switch is located under the top plastic tab as shown in Figure 2-4. Use the rese

Installing the SmartSwitch 9000 Module2-8

3-1 Chapter 3OperationThe 9F426-03 FDDI SmartSwitch Module is a four port switch module with three front panel FDDI interfaces and one INB-2 backplan

Operation3-2SMB-1 BusThe SMB-1 is a 1Mbs management bus located within the SmartSwitch 9000. This bus is utilized by all diagnostic controllers in the

3-3OperationINB InterfaceEach module that attaches to the INB has an INB Network Interface Block (NIB). The INB NIB converts canonical frames to fixed

Operation3-4i960 CoreThe i960 core provides the SNMP protocol stacks to support industry standard MIBs. Additionally, Cabletron enterprise extension M

4-1Chapter 4LANVIEW LEDsThe front panel LANVIEW LEDs indicate the status of the module and may be used as an aid in troubleshooting. Shown in Figure 4

LANVIEW LEDs4-2The functions of the two System Status LEDs, System Management Bus (SMB) and the CPU, are listed in Table 4-1.The functions of the INB

4-3LANVIEW LEDsThe functions of the FDDI receive LEDs are listed in Table 4-4.The functions of the FDDI Transmit LEDs are listed in Table 4-5.The FDDI

iNotice Notice Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior n

LANVIEW LEDs4-4The functions of the FDDI Status LEDs are listed in Table 4-6.Table 4-6. FDDI Status LEDs A P S B STATEGreen N/A N/A Green Ports Enabl

5-1Chapter 5SpecificationsTechnical SpecificationsCPUIntel i960 RISC based microprocessorMemory4 Meg. Flash Memory (expandable to 32 Meg.)16 Meg. DRAMSt

Specifications5-2SafetyThis equipment meets the safety requirements of:• UL 1950• CSA C22.2 No. 950 • EN 60950• IEC 950• EMI Requirements of FCC Part 1

A-1 AFPIM SpecificationsThis SmartSwitch 9000 module uses Fiber Port Interface Modules (FPIM) to provide front panel cable connections. The FPIMs are u

FPIM SpecificationsA-2Transmitter power parameters are listed in Table A-2.The link distance is up to 2 kilometers on the multimode fiber-optic cable as

A-3FPIM-05 and FPIM-07FPIM-05 and FPIM-07The FPIM-05 and FPIM-07 provide a Single-mode fiber connection. The FPIM-05 uses a MIC-style connector and the

FPIM SpecificationsA-4

Noticeii FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not

iiiNotice DOC Notice This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio

Noticeiv Safety Information CLASS 1 LASER TRANSCEIVERSThe FPIM-05 and FPIM-07 are Class 1 Laser ProductsThe FPIM-05 and FPIM-07 use Class 1 Laser tra

vNotice Safety Information CLASS 1 LASER TRANSCEIVERSLaser Radiation and Connectors When the connector is in place, all laser radiation remains withi

Noticevi DECLARATION OF CONFORMITY Application of Council Directive(s): 89/336/EEC73/23/EEC Manufacturer’s Name: Cabletron Systems, Inc. Manufacturer

vii Contents Chapter 1 Introduction Features..........................